Status of the control terminal block control inputs.
Important: Actual control commands may come from a source other than the control terminal block.

Default: Based on Drive Rating
Min/Max: 20/Drive Rated Volts
Display: 1 VAC

Default: 60 Hz
Min/Max: 15/400 Hz
Display: 1 Hz

Default: Based on Drive Rating
Min/Max: 0.0/(Drive Rated Amps × 2)
Display: 0.1 Amps

Default: 0.0 Hz
Min/Max: 0.0/400.0 Hz
Display: 0.1 Hz

Default: 60 Hz
Min/Max: 0/400 Hz
Display: 1 Hz

0 “Keypad” (Default)	• Integral keypad controls drive operation.
			• I/O Terminal 1 “Stop” = coast to stop.
			• When active, the Reverse key is also active unless
			  disabled by A434 [Reverse Disable].
						  
1 “3-Wire” 		I/O Terminal 1 “Stop” = stop according to the value set in
			P107 [Stop Mode].

2 “2-Wire” 		I/O Terminal 1 “Stop” = coast to stop.

3 “2-W Lvl Sens” 	Drive will restart after a “Stop” command when:
			• Stop is removed
			  and
			• Start is held active

4 “2-W Hi Speed” 	Important: There is greater potential voltage on the output
			terminals when using this option.
			• Outputs are kept in a ready-to-run state. The drive will
			  respond to a “Start” command within 10 ms.
			• I/O Terminal 1 “Stop” = coast to stop.

5 “Comm Port” 		• Remote communications. Refer to Appendix C 
			  for details.
			• I/O Terminal 1 “Stop” = coast to stop.

Active stop mode for all stop sources.

0 “Ramp, CF” (Default) 	Ramp to Stop. “Stop” command clears active fault.

1 “Coast, CF” 		Coast to Stop. “Stop” command clears active fault.

2 “DC Brake, CF” 	DC Injection Braking Stop. “Stop” command clears active
			fault.

3 “DCBrkAuto,CF” 	DC Injection Braking Stop with Auto Shutoff.
			• Standard DC Injection Braking for value set in A080 [DC
			  Brake Time].
			OR
			• Drive shuts off if the drive detects that the motor is
			  stopped.
			“Stop” command clears active fault.

4 “Ramp” 		Ramp to Stop.

5 “Coast” 		Coast to Stop.

6 “DC Brake” 		DC Injection Braking Stop.

7 “DC BrakeAuto” 	DC Injection Braking Stop with Auto Shutoff.
			• Standard DC Injection Braking for value set in A424 [DC
			  Brake Time].
			OR
			• Drive shuts off if current limit is exceeded.

0 “Drive Pot” (Default) Internal Frequency command from the potentiometer on the
			integral keypad.

1 “InternalFreq”        Internal frequency command from A409 [Internal Freq].

2 “0-10V Input” 	External frequency command from the 0-10V or ±10V analog
			input or remote potentiometer.

3 “4-20mA Input” 	External frequency command from the 4-20mA analog input.

4 “Preset Freq” 	External frequency command as defined by A410 - A413
			[Preset Freq x] when t201 - t202 [Digital Inx Sel] are
			programmed as “Preset Frequencies” and the digital inputs
			are active.

5 “Comm Port” 		External frequency command from the communications port.

Default: 10.0 Secs
Min/Max: 0.0/600.0 Secs
Display: 0.1 Secs

Default: 10.0 Secs
Min/Max: 0.1/600.0 Secs
Display: 0.1 Secs

0 “Disabled” (Default)
1 “Enabled”

0 “Ready/Idle” (Default)

1 “Factory Rset” 	 • After the reset function is complete, this parameter will set
			   itself back to “0”.
			 • Causes an F48 Params Defaulted fault.

1. Check remote wiring.
2. Verify communications programming for intentional fault

1. Monitor the incoming line for phase loss or line imbalance.
2. Check input line fuse.

1. An excessive motor load exists. Reduce load so drive output current 
   does not exceed the current set by parameter P103 [Motor OL Current].
2. Verify A453 [Boost Select] setting

1. Check for blocked or dirty heat sink fins. Verify that ambient 
   temperature has not exceeded 40°C (104°F) for IP30, NEMA UL 
   Type 1 installations or 50°C (122°F) for IP20/Open type installations.
2. Check fan.

1. Check the wiring between the drive and motor.
2. Check motor for grounded phase.
3. Replace drive if fault cannot be cleared.

1. Check the motor and drive output terminal wiring for a shorted condition.
2. Replace drive if fault cannot be cleared.

1. Clear the fault or cycle power to the drive.                                        
2. Program the drive parameters as needed.

1. Cycle power.              
2. Replace drive if fault cannot be cleared.

1. Cycle power.                                 
2. Check communications cabling.                                    
3. Check network adapter setting.
4. Check external network status.

1. If adapter was not intentionally disconnected, check wiring to the port. 
   Replace wiring, port expander, adapters or complete drive as required.
2. Check connection.
3. An adapter was intentionally disconnected.
4. Turn off using A304 [Comm Loss Action].

1. Cycle power.   
2. Replace drive if fault cannot be cleared.